20w50 too heavy?

BADAZZ89LX · Post by **BADAZZ89LX** » Wed Jun 25, 2008 4:34 pm

is 20w/50 weight oil too much for a dss 331?..they said it will be fine but ill lose HP..ive heard different views on this...some say itll kill the valves etc since they have to work extra hard to push the thicker oil...some say there is no drawbacks minus the hp loss....

i dont wanna ruin my new motor by running too thick of an oil

10w30 breaks down too easily for me to use

mightymouse0355 · Post by **mightymouse0355** » Wed Jun 25, 2008 8:37 pm

I run Vavoline VR1 20/50 weight and I wouldnt run anything else

PONY GUY · Post by **PONY GUY** » Wed Jun 25, 2008 8:57 pm

i run 20w50 as well in the warmer months . in the winter i run 10w30

BADAZZ89LX · Post by **BADAZZ89LX** » Wed Jun 25, 2008 10:43 pm

well..yea..id def go lighter in the winter even tho the car sits..ok..i guess ill be safe with this weight..i was also told it depends on how much clearence your motor has in it from when it was built..if it was built loose..you can run thicker oil..if it has tight specs..the thick oil will kill it

BADAZZ89LX · Post by **BADAZZ89LX** » Thu Jun 26, 2008 6:40 pm

anyone else?

Do-It-To-It · Post by **Do-It-To-It** » Thu Jun 26, 2008 7:46 pm

did a ton of runs on the dyno from unlimited hydroplanes to bad ass street engines to full nitrous engines on your bassic street engine makin 5 to 600 hp from 10-30 to 20-50 there was only a 3 to 5 hp difference we always used 20-50 in everything and in the winter when its cold use a oil pan heater on the car before ya fire it up bassically just a lizard tank heater taped to the bottom of the pan an hour before firing it up cause its so thick when its from 45degrees and lower 20-50 is the only oil to use and the brand that seemed to hold up better on all the bearings and interals was CASTROL

BADAZZ89LX · Post by **BADAZZ89LX** » Thu Jun 26, 2008 8:02 pm

id def put a thinner oil in there in the winter in case its semi warm and i actually drive it

rednotch · Post by **rednotch** » Fri Jun 27, 2008 12:50 am

thats all I've used in the red car chris. bearings where fine when I took it apart.

wazslow · Post by **wazslow** » Fri Jun 27, 2008 11:05 am

Always used 20-50 in mine. No problems...

HonkIfPartsFallOff · Post by **HonkIfPartsFallOff** » Fri Jun 27, 2008 10:32 pm

Your not going to "Kill" anything. It helps to know your bearing clearences when choosing and oil viscosity. Most older style drag motors are going to be looser and the thicker oil is beneficial. A newer modern engine with tight bearing clearences will require a 30 weight oil.

What do you mean by the 30 weight oil breaks down to easily for you?

BADAZZ89LX · Post by **BADAZZ89LX** » Sat Jun 28, 2008 8:28 am

did 4 passes in an hours time and got a tap

next day the tap was basically gone and has been

spokle to DSS the other day..he said id be fine with the 20/50..id just lose minimal HP

67camaro101 · Post by **67camaro101** » Sat Jun 28, 2008 1:29 pm

i use rotella 20-40

Smith · Post by **Smith** » Sat Jun 28, 2008 8:05 pm

BADAZZ89LX wrote:did 4 passes in an hours time and got a tap

next day the tap was basically gone and has been

spokle to DSS the other day..he said id be fine with the 20/50..id just lose minimal HP

Id think the tap is something else trying to tell you something. It "should" run fine with the 30wt......going to the thicker stuff is bandaiding something else.

BADAZZ89LX · Post by **BADAZZ89LX** » Sat Jun 28, 2008 8:17 pm

its going back to the shop 2morrow to figure out what is wrong if anything...

Smith · Post by **Smith** » Sat Jun 28, 2008 8:28 pm

Id prolly start with manually turning the oil pump and make sure your getting oil out of all the pushrods.

catchk9 · Post by **catchk9** » Sun Aug 17, 2008 8:52 pm

20/50 here also!

gmracing355 · Post by **gmracing355** » Mon Aug 18, 2008 2:31 am

I went from 20/50 to mobil 1 0/30 sythentic and went from low 11.30 to a best of 11.17. No problem with oil psi and make five runs that night.Im just trying to get her in the 10s on motor
Greg

GoneDragRacing.com

20w50 too heavy?

20w50 too heavy?

Re: 20w50 too heavy?

Re: 20w50 too heavy?

Re: 20w50 too heavy?

Re: 20w50 too heavy?

Re: 20w50 too heavy?

Re: 20w50 too heavy?

Re: 20w50 too heavy?

Re: 20w50 too heavy?

Re: 20w50 too heavy?

Re: 20w50 too heavy?

Re: 20w50 too heavy?

Re: 20w50 too heavy?

Re: 20w50 too heavy?

Re: 20w50 too heavy?

Re: 20w50 too heavy?

Re: 20w50 too heavy?